DIN rail unit for switching 2 blinds with motors from 230V to 16A. It is indicated for the control of blinds, curtains, awnings and other motors of the same type. The unit is also equipped with 2 binary inputs for voltage detection.
This module is used to control up to 2 blinds with independent power supply (from different phases, differentials or circuit breakers).
The recommended and most intuitive way is on the panel by sliding your finger vertically.
It can also be acted:
– on the A-Touch APP when allocated to a room
– in the A-touch APP when associated with a scenario
– use Voice commands in assistants such as SIRI.
The recommended and most intuitive way is on the panel by sliding your finger vertically.
It can also be acted:
– on the A-Touch APP when allocated to a room
– in the A-touch APP when associated with a scenario
– use Voice commands in assistants such as SIRI.
In the Atouch App, placing the blind in programming mode and then on the panel where you want to control it by sliding vertically between the keys.
In the App, put the blind in programming mode and then press a key to switch between open, stop and close.
On the D-2SHUTT module press the “PROG” button and then on the exit, then make a vertical or horizontal slide (between two keys) of a panel where you want to control the blind.
In the D-2SHUTT module, press the “PROG” button and then at the exit, then press a key on the panel that you want to command to switch, so it will open, stop and close.
In the Atouch App, placing the blind in programming mode and then on the panel where you want to control it by sliding vertically between the keys.
In the App, put the blind in programming mode and then press a key to switch between open, stop and close.
On the D-2SHUTT module press the “PROG” button and then on the exit, then make a vertical or horizontal slide (between two keys) of a panel where you want to control the blind.
In the D-2SHUTT module, press the “PROG” button and then at the exit, then press a key on the panel that you want to command to switch, so it will open, stop and close.
The easiest way to configure all blinds is using D-BUSSUPPLY.
In D-BUSSUPPLY, press “PROG” and the Red Led lights up.
Press the “LOCK” button for 5 seconds and you will hear a long “beep” in all the wall modules and in the switchboard modules you should see the LEDs of the blinds on.
Make a slide or press the key on the panel that you want to use to control all the blinds.
On D-BUSSUPPLY3.0, press “PROG” and the Red Led lights up.
Press the shutters button and you will hear a long “beep” in all the wall modules and in the frame modules you should see the LEDs of the blinds on.
Make a slide or press the key on the panel that you want to use to control all the blinds.
In the APP Atouch put all the blinds in programming by selecting each one and make a slide or press the key on the panel that you want to use to control all the blinds.
The easiest way to configure all blinds is using D-BUSSUPPLY.
In D-BUSSUPPLY, press “PROG” and the Red Led lights up.
Press the “LOCK” button for 5 seconds and you will hear a long “beep” in all the wall modules and in the switchboard modules you should see the LEDs of the blinds on.
Make a slide or press the key on the panel that you want to use to control all the blinds.
On D-BUSSUPPLY3.0, press “PROG” and the Red Led lights up.
Press the shutters button and you will hear a long “beep” in all the wall modules and in the frame modules you should see the LEDs of the blinds on.
Make a slide or press the key on the panel that you want to use to control all the blinds.
In the APP Atouch put all the blinds in programming by selecting each one and make a slide or press the key on the panel that you want to use to control all the blinds.
Attention: Over time, it is possible that the shutter motor becomes slower, which implies that the information on the position of the shutters in the application is not the most correct. This condition does not imply a change in the A-touch application, but in the engine speed.
By correctly timing the opening/closing time of the blinds, this information is transferred to the App in order to inform the position of the blinds.
Attention: Over time, it is possible that the shutter motor becomes slower, which implies that the information on the position of the shutters in the application is not the most correct. This condition does not imply a change in the A-touch application, but in the engine speed.
By correctly timing the opening/closing time of the blinds, this information is transferred to the App in order to inform the position of the blinds.
The binary inputs of the D-2SHUTT are preferably used with sensors such as anemometers or a rain sensor in order to close or open the shutters of that module when the state of these sensors changes.
They can also be used for any other output of the Atouch system, but in this case a D-16VIN is recommended.
The binary inputs of the D-2SHUTT are preferably used with sensors such as anemometers or a rain sensor in order to close or open the shutters of that module when the state of these sensors changes.
They can also be used for any other output of the Atouch system, but in this case a D-16VIN is recommended.
Press the left microswitch on the panel over the module for 10s until you hear a “beep”.
This action will clear the module’s memory, as will all the keys that operated on the blind.
Press the left microswitch on the panel over the module for 10s until you hear a “beep”.
This action will clear the module’s memory, as will all the keys that operated on the blind.
Subscribe to our newsletter and receive news, tips and offers Atouch
