Programmable thermostat with temperature timing. 230VAC output to be used with radiator, underfloor heating and others.
The W-THERMO16 module is a thermostat dedicated to high electrical loads to be placed on the wall (W= Wall), it works locally or remotely paired with a T-OLED panel. It is the T-OLED that reads and reports the temperature in the room where it is installed. Among other functions, it performs weekly scheduling and summer/winter cycle control.
Yes, it supports and powers T-K4 or T-OLED panels.
Pairing a T-OLED is automatic when placed on top of a W-THERMO16.
Cannot support and power T-SEC panels as these need to be installed in a W-4SEC
Yes, it supports and powers T-K4 or T-OLED panels.
Pairing a T-OLED is automatic when placed on top of a W-THERMO16.
Cannot support and power T-SEC panels as these need to be installed in a W-4SEC
Like any module in the clima control range, the W-THERMO16 must be paired with a T-OLED.
It is the T-OLED that has a probe to read the temperature and informs the W-THERMO16 so that it can decide on/off the machine according to the programmed parameters.
Pairing an OLED is automatic when placed on top of a W-THERMO16.
Like any module in the clima control range, the W-THERMO16 must be paired with a T-OLED.
It is the T-OLED that has a probe to read the temperature and informs the W-THERMO16 so that it can decide on/off the machine according to the programmed parameters.
Pairing an OLED is automatic when placed on top of a W-THERMO16.
The W-THERMO must be paired with a T-OLED in secondary mode (without the icon shown on the display), press PROG on the W-THERMO, the LED will turn red, then press simultaneously on the lower left and upper right keys of the T -OLED and the pairing is done, at this point you should see the display information update.
The W-THERMO must be paired with a T-OLED in secondary mode (without the icon shown on the display), press PROG on the W-THERMO, the LED will turn red, then press simultaneously on the lower left and upper right keys of the T -OLED and the pairing is done, at this point you should see the display information update.
No, when a T-OLED is placed on a W-THERMO16 it is always paired by default. In order to control a D-THERMO, you will have to pair it with the secondary machine of the W-THERMO16. Alternatively, you can pair it with a T-OLED that is placed on another W module (W-2ONOFF, W-1SHUT or W-INPKEY).
No, when a T-OLED is placed on a W-THERMO16 it is always paired by default. In order to control a D-THERMO, you will have to pair it with the secondary machine of the W-THERMO16. Alternatively, you can pair it with a T-OLED that is placed on another W module (W-2ONOFF, W-1SHUT or W-INPKEY).
The W-THERMO16 only has one zone, which can be controlled with 1 relay output.
The W-THERMO16 only has one zone, which can be controlled with 1 relay output.
There is no limit of units per type of modules in an Atouch home.
There is no limit of units per type of modules in an Atouch home.
The cycle can be changed via App 3.0 or on a T-OLED associated with a thermostat.
In the App, press the clima control button on the bottom bar and choose the cycle.
On the T-OLED enter configuration mode and toggle the cycle from summer mode to winter mode.
The cycle can be changed via App 3.0 or on a T-OLED associated with a thermostat.
In the App, press the clima control button on the bottom bar and choose the cycle.
On the T-OLED enter configuration mode and toggle the cycle from summer mode to winter mode.
This module only allows you to control one heating machine.
This module only allows you to control one heating machine.
In order to have two machines in a single room and in a single panel T-OLED with probe, a chained pairing is necessary, so the T-OLED is paired with the Thermo, which will be the main machine in the room, and then the secondary machine is programmed to follow the primary.
In order to have two machines in a single room and in a single panel T-OLED with probe, a chained pairing is necessary, so the T-OLED is paired with the Thermo, which will be the main machine in the room, and then the secondary machine is programmed to follow the primary.
To define the type and machine you will have to enter the configuration menu.
On the T-OLED panel, ensure that it is in climate control mode by pressing the lower left and upper right keys simultaneously and briefly.
Make sure the thermostat is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu. Use the (-) key to navigate to the “Unit Type” menu and choose by pressing the lower left key.
To define the type and machine you will have to enter the configuration menu.
On the T-OLED panel, ensure that it is in climate control mode by pressing the lower left and upper right keys simultaneously and briefly.
Make sure the thermostat is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu. Use the (-) key to navigate to the “Unit Type” menu and choose by pressing the lower left key.
To edit the schedule you will have to enter the menu.
On the T-OLED panel, ensure that it is in clima control mode by pressing simultaneously and briefly on the lower left and upper right keys.
Make sure the thermostat is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
The first option will appear as “Program” by pressing the lower left key and change between “On” and “Off”, confirm by pressing the lower left key.
The “Cycle” option will appear and you can choose Winter or Summer.
Navigate to “Summer” and “Winter” and set the times and temperatures by day of the week for each of the cycles.
To edit the schedule you will have to enter the menu.
On the T-OLED panel, ensure that it is in clima control mode by pressing simultaneously and briefly on the lower left and upper right keys.
Make sure the thermostat is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
The first option will appear as “Program” by pressing the lower left key and change between “On” and “Off”, confirm by pressing the lower left key.
The “Cycle” option will appear and you can choose Winter or Summer.
Navigate to “Summer” and “Winter” and set the times and temperatures by day of the week for each of the cycles.
You can change the temperature in two ways via the APP or via the panel where you measure the temperature to be changed:
a) APP – In the lower bar, navigate to Clima Control, find the room you want to change and increase or decrease the “Target Temperature” using the “+” and “-“;
b) On the room panel, ensure that it is in climate mode by pressing the lower left and upper right keys simultaneously and briefly.
Check whether it is on or off by pressing the key and press the “+” and “-” key to change the “Target Temperature”.
If you have the schedule turned on, these actions overlap until the next scheduled event.
You can change the temperature in two ways via the APP or via the panel where you measure the temperature to be changed:
a) APP – In the lower bar, navigate to Clima Control, find the room you want to change and increase or decrease the “Target Temperature” using the “+” and “-“;
b) On the room panel, ensure that it is in climate mode by pressing the lower left and upper right keys simultaneously and briefly.
Check whether it is on or off by pressing the key and press the “+” and “-” key to change the “Target Temperature”.
If you have the schedule turned on, these actions overlap until the next scheduled event.
These changes are in effect until the next scheduled event occurs. If you do not have active schedules in the “Program” Menu, they will remain until you change them again.
These changes are in effect until the next scheduled event occurs. If you do not have active schedules in the “Program” Menu, they will remain until you change them again.
Yes, a T-OLED paired with 1 or 2 Thermo modules controlling 1 or 2 machines for the same room can always remain in secondary Air Conditioning (without ).
To permanently switch between Primary automation mode and Secondary clima control mode, press the lower left and upper right buttons simultaneously for 5 seconds. The presence or absence of respectively indicates automation or clima control mode.
If you are in automation mode and just want to change it temporarily press the keys momentarily.
Yes, a T-OLED paired with 1 or 2 Thermo modules controlling 1 or 2 machines for the same room can always remain in secondary Air Conditioning (without ).
To permanently switch between Primary automation mode and Secondary clima control mode, press the lower left and upper right buttons simultaneously for 5 seconds. The presence or absence of respectively indicates automation or clima control mode.
If you are in automation mode and just want to change it temporarily press the keys momentarily.
This module can be mounted anywhere, as long as the BUS communication and humidity conditions are safeguarded so that it works correctly.
This module can be mounted anywhere, as long as the BUS communication and humidity conditions are safeguarded so that it works correctly.
No, this module does not have binary inputs. The inputs are used to connect motion sensors, brightness, timers or others.
No, this module does not have binary inputs. The inputs are used to connect motion sensors, brightness, timers or others.
To reset this module to its original settings, press the two buttons for 10 seconds. This will clear the name, panel association and all machine parameters.
To reset this module to its original settings, press the two buttons for 10 seconds. This will clear the name, panel association and all machine parameters.
Subscribe to our newsletter and receive news, tips and offers Atouch
