Programmable thermostat with temperature timing. It can be used for radiators, water underfloor heating, fan 2-tube convectors and air conditioning.
The W-THERMO module is a thermostat to be placed on the wall (W= Wall), it works paired, locally or remotely, with a T-OLED keypad. It is the T-OLED that reads and reports the temperature in the room where it is installed.
Among other functions, it performs weekly scheduling and summer/winter cycle control.
Yes, it supports and powers T-K4 or T-OLED panels.
Pairing a T-OLED is automatic when placed on top of a W-THERMO.
Cannot support and power T-SEC panels as these need to be installed in a W-4SEC.
Yes, it supports and powers T-K4 or T-OLED panels.
Pairing a T-OLED is automatic when placed on top of a W-THERMO.
Cannot support and power T-SEC panels as these need to be installed in a W-4SEC.
Like any module in the climate control range, W-THERMO must be paired with a T-OLED.
It is the T-OLED that has a probe to read the temperature and informs the W-THERMO so that it can decide on/off the machine according to the programmed parameters.
Pairing an OLED is automatic when placed on top of a W-THERMO.
Like any module in the climate control range, W-THERMO must be paired with a T-OLED.
It is the T-OLED that has a probe to read the temperature and informs the W-THERMO so that it can decide on/off the machine according to the programmed parameters.
Pairing an OLED is automatic when placed on top of a W-THERMO.
The W-THERMO must be paired with a T-OLED in secondary mode (not shown on the display), press “PROG” on the W-THERMO, the LED will turn red, then press simultaneously on the lower left and upper right keys of the T -OLED and the pairing is done, at this point you should see the display information update.
The W-THERMO must be paired with a T-OLED in secondary mode (not shown on the display), press “PROG” on the W-THERMO, the LED will turn red, then press simultaneously on the lower left and upper right keys of the T -OLED and the pairing is done, at this point you should see the display information update.
No, when a T-OLED is placed on a W-THERMO it is always paired by default. For this to control a D-THERMO you will have to pair it with a secondary machine of the W-THERMO. Alternatively, you can pair it with a T-OLED that is placed on another W module (W-2ONOFF, W-1SHUT or W-INPKEY).
No, when a T-OLED is placed on a W-THERMO it is always paired by default. For this to control a D-THERMO you will have to pair it with a secondary machine of the W-THERMO. Alternatively, you can pair it with a T-OLED that is placed on another W module (W-2ONOFF, W-1SHUT or W-INPKEY).
The W-THERMO only makes one zone, which can heat different rooms or floors, this one has connections for 3 speeds plus a common valve. The panel that is paired in a room with this W-THERMO can control another secondary heating or cooling machine.
The W-THERMO only makes one zone, which can heat different rooms or floors, this one has connections for 3 speeds plus a common valve. The panel that is paired in a room with this W-THERMO can control another secondary heating or cooling machine.
There is no limit of units per module type in an Atouch home.
There is no limit of units per module type in an Atouch home.
The cycle can be changed via App 3.0 or on a T-OLED associated with any thermostat.
In APP 3.0, press the clima control button on the bottom bar and choose the cycle.
On the T-OLED enter configuration mode and toggle the cycle from summer mode to winter mode.
The cycle can be changed via App 3.0 or on a T-OLED associated with any thermostat.
In APP 3.0, press the clima control button on the bottom bar and choose the cycle.
On the T-OLED enter configuration mode and toggle the cycle from summer mode to winter mode.
W-THERMO can be used on different machines:
2-pipe fan coil units
Radiators (dry starter contact)
Water underfloor heating via electrovalve
Air Conditioning (dry contact)
Consult us for more details or send us the reference of your machines.
W-THERMO can be used on different machines:
2-pipe fan coil units
Radiators (dry starter contact)
Water underfloor heating via electrovalve
Air Conditioning (dry contact)
Consult us for more details or send us the reference of your machines.
In order to have two machines in a single room and in a single panel T-OLED with probe, a chained pairing is necessary, so the T-OLED is paired with the Thermo, which will be the main machine in the room, and then the secondary machine is programmed to follow the primary.
In order to have two machines in a single room and in a single panel T-OLED with probe, a chained pairing is necessary, so the T-OLED is paired with the Thermo, which will be the main machine in the room, and then the secondary machine is programmed to follow the primary.
To define the type of machine you will have to enter the configuration menu. On the T-OLED panel, ensure that it is in climate control mode by pressing the lower left and upper right keys simultaneously and briefly.
Make sure the thermostat output is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
Use the (-) key to navigate to the “Unit Type” menu and choose by pressing the lower left key.
To define the type of machine you will have to enter the configuration menu. On the T-OLED panel, ensure that it is in climate control mode by pressing the lower left and upper right keys simultaneously and briefly.
Make sure the thermostat output is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
Use the (-) key to navigate to the “Unit Type” menu and choose by pressing the lower left key.
To edit the schedule you will have to enter the menu. On the T-OLED panel, ensure that it is in climate control mode by pressing the lower left and upper right keys simultaneously and briefly.
Make sure the thermostat output is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
The first option will appear as “Program” by pressing the lower left key and change between “On” and “Off”, confirm by pressing the lower left key.
The “Cycle” option will appear and you can choose Winter or Summer.
Navigate to “Summer” and “Winter” and set the times and temperatures by day of the week for each of the cycles.
To edit the schedule you will have to enter the menu. On the T-OLED panel, ensure that it is in climate control mode by pressing the lower left and upper right keys simultaneously and briefly.
Make sure the thermostat output is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
The first option will appear as “Program” by pressing the lower left key and change between “On” and “Off”, confirm by pressing the lower left key.
The “Cycle” option will appear and you can choose Winter or Summer.
Navigate to “Summer” and “Winter” and set the times and temperatures by day of the week for each of the cycles.
You can change the temperature in two ways via the APP or via the panel where you measure the temperature to be changed:
a) APP – In the lower bar, navigate to Clima Control, find the room you want to change and increase or decrease the “Target Temperature” using the “+” and “-“;
b) on the room panel it ensures that it is in climate mode
Check whether it is on or off by pressing the key and press the “+” and “-” key to change the “Target Temperature”.
If you have the schedule turned on, these actions overlap until the next scheduled event.
You can change the temperature in two ways via the APP or via the panel where you measure the temperature to be changed:
a) APP – In the lower bar, navigate to Clima Control, find the room you want to change and increase or decrease the “Target Temperature” using the “+” and “-“;
b) on the room panel it ensures that it is in climate mode
Check whether it is on or off by pressing the key and press the “+” and “-” key to change the “Target Temperature”.
If you have the schedule turned on, these actions overlap until the next scheduled event.
These changes are in effect until the next scheduled event occurs. If you do not have active schedules in the “Program” Menu, they will remain until you change them again.
These changes are in effect until the next scheduled event occurs. If you do not have active schedules in the “Program” Menu, they will remain until you change them again.
Yes, a T-OLED paired with 1 or 2 Thermo modules controlling 1 or 2 machines for the same room can always be in secondary Air Conditioning mode (without ).
To permanently switch between Primary automation mode and Secondary climate control mode, press the lower left and upper right buttons simultaneously for 5 seconds. The presence or absence of respectively indicates automation or clima control mode.
If you are in automation mode and just want to change it temporarily press the keys momentarily.
Yes, a T-OLED paired with 1 or 2 Thermo modules controlling 1 or 2 machines for the same room can always be in secondary Air Conditioning mode (without ).
To permanently switch between Primary automation mode and Secondary climate control mode, press the lower left and upper right buttons simultaneously for 5 seconds. The presence or absence of respectively indicates automation or clima control mode.
If you are in automation mode and just want to change it temporarily press the keys momentarily.
No, this module does not have binary inputs. The inputs are used to connect motion sensors, brightness, timers or others.
No, this module does not have binary inputs. The inputs are used to connect motion sensors, brightness, timers or others.
To reset this module to its original settings, press the two buttons for 10 seconds. This will clear the name, panel association and all machine parameters.
To reset this module to its original settings, press the two buttons for 10 seconds. This will clear the name, panel association and all machine parameters.
Subscribe to our newsletter and receive news, tips and offers Atouch
