Command for switching 2 independent circuits with potential free contacts up to 5A. This unit is equipped with a radio frequency transmitter / receiver. It is indicated for contact action for gate controls or other low-power loads.
The W-2VLESS module is used to control up to 2 low power dry contacts. Typically used for garage door control due to its RF signal reception capability for use with our RC-4BRF control, systems where the nature of the contact to which you want to create a parallel drive is unknown.
It also serves as an RF signal receiver expander.
It is typically used in refurbishments and allows to replace the traditional switchgear by our module with communication and drive via BUS, to install reliable home automation by wire without building works in the house.
On top of this module can be placed an Atouch touch panel for automation as one of Clima Control or Audio.
We recommend the APP to associate an output to a key.
Go to the left menu and select PROGRAM, find the output and put it in programming by pressing the option on the right side, press the key (the output will no longer appear as in programming in the APP).
We recommend the APP to associate an output to a key.
Go to the left menu and select PROGRAM, find the output and put it in programming by pressing the option on the right side, press the key (the output will no longer appear as in programming in the APP).
The outputs of this module can be programmed without App, just with a touch panel installed on it. By pressing the left microswitch on the lower face of the touch panel.
One click corresponds to the first output, two clicks corresponds to the second output, three clicks corresponds to both outputs simultaneously. Then tap a key on the touch panel to be associated with the output option you chose to program.
The outputs of this module can be programmed without App, just with a touch panel installed on it. By pressing the left microswitch on the lower face of the touch panel.
One click corresponds to the first output, two clicks corresponds to the second output, three clicks corresponds to both outputs simultaneously. Then tap a key on the touch panel to be associated with the output option you chose to program.
Go to the left menu and select DELETE find the output(s) and put them in programming, press the key, the output(s) no longer appear as being in programming in the APP.
Go to the left menu and select DELETE find the output(s) and put them in programming, press the key, the output(s) no longer appear as being in programming in the APP.
On the panel placed on the W-2vless module press the left microswitch of the panel to enter the programming mode of the output(s) from which you want to remove the key, 1-touch for output 1, 2-touch for output 2, three-touch for both outputs.
Press left microswitch on the panel for more than 2 seconds.
Press the key (on the panel) you want to remove.
On the panel placed on the W-2vless module press the left microswitch of the panel to enter the programming mode of the output(s) from which you want to remove the key, 1-touch for output 1, 2-touch for output 2, three-touch for both outputs.
Press left microswitch on the panel for more than 2 seconds.
Press the key (on the panel) you want to remove.
Go to the left menu and select PANEL SETUP press a key on the panel that has the key you want to remove from all outputs.
Choose the key and in the COMMAND option choose DELETE then confirm with the check in the upper right corner of the screen.
Go to the left menu and select PANEL SETUP press a key on the panel that has the key you want to remove from all outputs.
Choose the key and in the COMMAND option choose DELETE then confirm with the check in the upper right corner of the screen.
Go to the left menu and select DELETE find the output and select the more options symbol on the right side of the screen. Confirm by selecting the option and validate by pressing the checkmark in the upper right corner.
Go to the left menu and select DELETE find the output and select the more options symbol on the right side of the screen. Confirm by selecting the option and validate by pressing the checkmark in the upper right corner.
Yes, you can put outputs 1 and 2 of the W-2VLESS module on timer.
On the W-2VLESS module press the button of the output for 5 seconds and the LED of the output will blink once a second, which corresponds to a time of 1 second. By pressing the key you can blink 2,3,4,5,6 which corresponds to 1 minute, 5 minutes, 15 minutes, 30 minutes, 1 hour respectively.
After choosing the desired time press for 5 seconds to finish the process.
The timing of the outputs (1 and 2) must be done at the end of all other associations or programming.
The timing is of the output and therefore valid for any key that activates this output and thus prevails over keys with timers programmed via APP.
Yes, you can put outputs 1 and 2 of the W-2VLESS module on timer.
On the W-2VLESS module press the button of the output for 5 seconds and the LED of the output will blink once a second, which corresponds to a time of 1 second. By pressing the key you can blink 2,3,4,5,6 which corresponds to 1 minute, 5 minutes, 15 minutes, 30 minutes, 1 hour respectively.
After choosing the desired time press for 5 seconds to finish the process.
The timing of the outputs (1 and 2) must be done at the end of all other associations or programming.
The timing is of the output and therefore valid for any key that activates this output and thus prevails over keys with timers programmed via APP.
Press for 5 seconds on the output button.
Press for 5 seconds on the output button.
Make sure PROG LOCK is not active.
If on any D-BUSSUPPLY in the house the “LOCK” LED is flashing constantly repeatedly you will have to press 2 seconds on the “LOCK” to remove this inhibition to programming.
Make sure PROG LOCK is not active.
If on any D-BUSSUPPLY in the house the “LOCK” LED is flashing constantly repeatedly you will have to press 2 seconds on the “LOCK” to remove this inhibition to programming.
These modules communicate via the BUS protocol which is referenced to a neutral, meaning you only need one more wire in your house to ensure you have BUS everywhere.
These modules communicate via the BUS protocol which is referenced to a neutral, meaning you only need one more wire in your house to ensure you have BUS everywhere.
Subscribe to our newsletter and receive news, tips and offers Atouch
