Shutter control for 230V ~ to 16A motors. It is indicated for the control of blinds, blinds, awnings, curtains or similar motors.
This module is used to control a roller blind. It is also the base and power supply for touch panel (T-K4 or T-OLED).
The recommended and most intuitive way is on the panel by sliding your finger vertically.
It can also be actuated:
– on the APP A-Touch when allocated to a room
– in the APP A-touch when associated to a scenario
– using Voice commands on assistants such as SIRI.
The recommended and most intuitive way is on the panel by sliding your finger vertically.
It can also be actuated:
– on the APP A-Touch when allocated to a room
– in the APP A-touch when associated to a scenario
– using Voice commands on assistants such as SIRI.
In the Atouch App by placing the shutter in programming and then on the panel where you want to control by sliding vertically between keys.
In the App by putting the shutter in programming and then pressing a key where it will switch between open, stop and close.
Press on the left microswitch under the panel where the W-1SHUTT is placed and then make a vertical or horizontal slide (between two keys) of a panel where you want to control the shutter.
Press on the left microswitch under the panel where the W-1SHUTT is placed and then on the panel key to toggle open, stop and close where you want to command the shutter.
In the Atouch App by placing the shutter in programming and then on the panel where you want to control by sliding vertically between keys.
In the App by putting the shutter in programming and then pressing a key where it will switch between open, stop and close.
Press on the left microswitch under the panel where the W-1SHUTT is placed and then make a vertical or horizontal slide (between two keys) of a panel where you want to control the shutter.
Press on the left microswitch under the panel where the W-1SHUTT is placed and then on the panel key to toggle open, stop and close where you want to command the shutter.
In the Atouch App by placing several blinds in programming and then on the panel where you want to control by sliding vertically between keys.
In the App putting several blinds in programming and then pressing a key where you want to control, so it will switch between open, stop and close.
Press on the left microswitch under the panel where the W-1SHUTT are placed and then make a vertical or horizontal slide (between two keys) of a panel where you want to control the shutter.
Press on the left microswitch under the panel where the W-1SHUTT are placed and then on the panel key to toggle open, stop and close where you want to control the shutter.
In the Atouch App by placing several blinds in programming and then on the panel where you want to control by sliding vertically between keys.
In the App putting several blinds in programming and then pressing a key where you want to control, so it will switch between open, stop and close.
Press on the left microswitch under the panel where the W-1SHUTT are placed and then make a vertical or horizontal slide (between two keys) of a panel where you want to control the shutter.
Press on the left microswitch under the panel where the W-1SHUTT are placed and then on the panel key to toggle open, stop and close where you want to control the shutter.
The easiest way to configure all the blinds is to use the D-BUSSUPPLY.
On the D-BUSSUPPLY press the “PROG” and the Red Led lights up.
Press the “LOCK” button for 5 seconds and you will hear a long “beep” on all the wall modules and on the frame modules you should see the blinds LEDs on.
Make a slide or press the key on the paanel you want to use to control all the blinds.
On the D-BUSSUPPLY3.0 press “PROG” and the Red Led lights up.
Press the shutters button and you will hear a long “beep” on all the wall modules and on the frame modules you should see the LEDs of the shutters on.
Make a slide or press the key on the panel you want to use to control all the blinds.
In the Atouch APP put all the blinds in programming by selecting each one and make a slide or press the key on the panel you want to use to control all the blinds.
The easiest way to configure all the blinds is to use the D-BUSSUPPLY.
On the D-BUSSUPPLY press the “PROG” and the Red Led lights up.
Press the “LOCK” button for 5 seconds and you will hear a long “beep” on all the wall modules and on the frame modules you should see the blinds LEDs on.
Make a slide or press the key on the paanel you want to use to control all the blinds.
On the D-BUSSUPPLY3.0 press “PROG” and the Red Led lights up.
Press the shutters button and you will hear a long “beep” on all the wall modules and on the frame modules you should see the LEDs of the shutters on.
Make a slide or press the key on the panel you want to use to control all the blinds.
In the Atouch APP put all the blinds in programming by selecting each one and make a slide or press the key on the panel you want to use to control all the blinds.
Attention: Over time it is possible that the motor of the blinds becomes slower, which implies that the information of the position of the blinds in the application is not the most correct. This condition does not imply a change in the A-touch application, but rather in the speed of the motor.
By timing the opening/closing time of the blinds correctly, this information passes to the App in order to inform which position the blinds are in.
Attention: Over time it is possible that the motor of the blinds becomes slower, which implies that the information of the position of the blinds in the application is not the most correct. This condition does not imply a change in the A-touch application, but rather in the speed of the motor.
By timing the opening/closing time of the blinds correctly, this information passes to the App in order to inform which position the blinds are in.
Press and hold the left microswitch on the panel above the module for 10s until you hear a “beep”.
This action will clear the memory of the module, like all the keys that acted on the shutter.
Press and hold the left microswitch on the panel above the module for 10s until you hear a “beep”.
This action will clear the memory of the module, like all the keys that acted on the shutter.
Subscribe to our newsletter and receive news, tips and offers Atouch
