DIN rail unit for switching 4 shutters with motors from 230V to 16A. It is indicated for the control of blinds, curtains, awnings and other motors of the same type. The unit is also equipped with 4 binary inputs for voltage detection.
This module is used to control up to 4 shutters. with independent power supply (form distinct phase, diferencial or circuit brackers)
The most user friendly way is via a vertical slide.
Also possible:
– in the A-Touch APP when alocatted to a room;
– in the A-Touch APP when alocatted to a scenario;
– via the voice assitents such as SIRI.
The most user friendly way is via a vertical slide.
Also possible:
– in the A-Touch APP when alocatted to a room;
– in the A-Touch APP when alocatted to a scenario;
– via the voice assitents such as SIRI.
Using the Atouch APP place the shutter in programing mode and then slide between to keys in the touch panel.
Using the Atouch APP place the shutter in programing mode and then press one key in the touch panel to toggle between open stop close.
On the D-4SHUTT module press “PROG” and after chose the output, then on the desired touch panel make a vertical or horizontal slide between keys.
On the D-4SHUTT module press “PROG” and after chose the output, then on the desired touch panel press a key, this way the shutter will toglle between open, stop and close.
Using the Atouch APP place the shutter in programing mode and then slide between to keys in the touch panel.
Using the Atouch APP place the shutter in programing mode and then press one key in the touch panel to toggle between open stop close.
On the D-4SHUTT module press “PROG” and after chose the output, then on the desired touch panel make a vertical or horizontal slide between keys.
On the D-4SHUTT module press “PROG” and after chose the output, then on the desired touch panel press a key, this way the shutter will toglle between open, stop and close.
Using the Atouch APP place several shutters in programing mode and then slide between keys in the touch panel.
Using the Atouch APP place several shutters in programing mode and then press one key in the touch panel to toggle between open stop close.
On the D-4SHUTT module press “PROG” and after chose one or two outputs, you can them execute the same steps on other shutter modules, then on the desired touch panel make a vertical or horizontal slide between keys.
On the D-4SHUTT module press “PROG” and after chose one or two outputs, you can them execute the same steps on other shutter modules, then on the desired touch panel press a key, this way the shutter will toglle between open, stop and close.
Using the Atouch APP place several shutters in programing mode and then slide between keys in the touch panel.
Using the Atouch APP place several shutters in programing mode and then press one key in the touch panel to toggle between open stop close.
On the D-4SHUTT module press “PROG” and after chose one or two outputs, you can them execute the same steps on other shutter modules, then on the desired touch panel make a vertical or horizontal slide between keys.
On the D-4SHUTT module press “PROG” and after chose one or two outputs, you can them execute the same steps on other shutter modules, then on the desired touch panel press a key, this way the shutter will toglle between open, stop and close.
The easiest way to program all shutters is using the D-BUSSUPPLY.
In the D-BUSSUPLY press “PROG” button and the red LED will ligth up.
Press the “LOCK” button for 5 seconds, the wall shutter modules will make a sound and the main switchboard shutter modules will ligth up the LEDs.
Slide your finger or press a key on the touch panel that you want to control all the shutters.
In the D-BUSSUPLY30. press “PROG” button and the red LED will ligth up.
Press the “Shutter” button for 5 seconds, the wall shutter modules will make a sound and the main switchboard shutter modules will ligth up the LEDs.
Slide your finger or press a key on the touch panel that you want to control all the shutters.
In the APP put one by one all shutters in programing then slide your finger or press a key on the touch panel that you want to control all the shutters.
The easiest way to program all shutters is using the D-BUSSUPPLY.
In the D-BUSSUPLY press “PROG” button and the red LED will ligth up.
Press the “LOCK” button for 5 seconds, the wall shutter modules will make a sound and the main switchboard shutter modules will ligth up the LEDs.
Slide your finger or press a key on the touch panel that you want to control all the shutters.
In the D-BUSSUPLY30. press “PROG” button and the red LED will ligth up.
Press the “Shutter” button for 5 seconds, the wall shutter modules will make a sound and the main switchboard shutter modules will ligth up the LEDs.
Slide your finger or press a key on the touch panel that you want to control all the shutters.
In the APP put one by one all shutters in programing then slide your finger or press a key on the touch panel that you want to control all the shutters.
Attention: Over time it is possible that the motor of the blinds becomes slower, which implies that the information of the position of the blinds in the application is not the most correct. This condition does not imply a change in the A-touch application, but rather in the speed of the motor.
By timing the opening/closing time of the blinds correctly, this information passes to the App in order to inform which position the blinds are in.
Attention: Over time it is possible that the motor of the blinds becomes slower, which implies that the information of the position of the blinds in the application is not the most correct. This condition does not imply a change in the A-touch application, but rather in the speed of the motor.
By timing the opening/closing time of the blinds correctly, this information passes to the App in order to inform which position the blinds are in.
The binary inputs of the D-4SHUTT are preferably used with sensors such as anemometers or rain sensors in order to close or open the blinds of that module when the status of these sensors changes.
They can also be used for any other output of the Atouch system but in this case a D-16VIN is recommended.
The binary inputs of the D-4SHUTT are preferably used with sensors such as anemometers or rain sensors in order to close or open the blinds of that module when the status of these sensors changes.
They can also be used for any other output of the Atouch system but in this case a D-16VIN is recommended.
Press the left microswitch on the keypad above the module for 10s until you hear a “beep”.
This action will clear the memory of the module, as well as all the keys that acted on the roller shutter.
Press the left microswitch on the keypad above the module for 10s until you hear a “beep”.
This action will clear the memory of the module, as well as all the keys that acted on the roller shutter.
Subscribe to our newsletter and receive news, tips and offers Atouch
