Glass touch panel for the Security System. It is equipped with OLED display and 14 touch keys.
To clean your keyboards, use a damp cloth with soap or diluted detergent.
The use of glass cleaner, alcohol or thinner when in contact with the back part weakens the glue and may lead to replacement of the keyboard with exclusion of warranty.
This functionality is now present using APP 3 and 5 together with D-Gateway 3.0 and 5.0 in all new Atouch homes.
You can press the left microswicth present on the underside of each keyboard for 2 seconds, then press it again for 5 seconds and the backlight will turn off. Repeating the process turns the backlight on again.
This functionality is now present using APP 3 and 5 together with D-Gateway 3.0 and 5.0 in all new Atouch homes.
You can press the left microswicth present on the underside of each keyboard for 2 seconds, then press it again for 5 seconds and the backlight will turn off. Repeating the process turns the backlight on again.
T-SEC is the glass tactile keypad dedicated to Atouch’s integrated Safety system. The integration of automation with security allows:
T-SEC is the glass tactile keypad dedicated to Atouch’s integrated Safety system. The integration of automation with security allows:
T-SEC has functions of:
Using the Atouch security system
T-SEC has functions of:
Using the Atouch security system
No, T-SEC keyboards can only be mounted on W-4SEC modules.
No, T-SEC keyboards can only be mounted on W-4SEC modules.
To enter the user code you need to press the “Key” symbol (common key with #1) and then enter your 4-digit code.
It is recommended that after installing the system you delete the code that goes by default.
To enter the user code you need to press the “Key” symbol (common key with #1) and then enter your 4-digit code.
It is recommended that after installing the system you delete the code that goes by default.
To add or remove user codes you need to enter the manager code.
Add a new one, or change it by entering a new one and removing the previous one.
To add or remove user codes you need to enter the manager code.
Add a new one, or change it by entering a new one and removing the previous one.
There are 3 levels with distinct codes:
There are 3 levels with distinct codes:
The name of the zones is editable only using the Atouch APP.
The name of the zones is editable only using the Atouch APP.
o configure the type of security zone you will need to access the installer menu.
The different zone types are:
o configure the type of security zone you will need to access the installer menu.
The different zone types are:
When arming in Full Mode the status of all zones is monitored.
Arming in Night Mode monitors the status of all zones except Immediate Interior and Delayed Interior.
Arming in Garage Mode monitors the status of all zones except Interior Immediate, Interior Delayed, Peripheral Immediate and Peripheral Delayed
When arming in Full Mode the status of all zones is monitored.
Arming in Night Mode monitors the status of all zones except Immediate Interior and Delayed Interior.
Arming in Garage Mode monitors the status of all zones except Interior Immediate, Interior Delayed, Peripheral Immediate and Peripheral Delayed
To arm via APP use the Security view and press the respective Icon, you will be prompted for a user code.
To arm via T-SEC enter one of the user codes and wait for it to arm in Full mode, if you want another one press:
To arm via APP use the Security view and press the respective Icon, you will be prompted for a user code.
To arm via T-SEC enter one of the user codes and wait for it to arm in Full mode, if you want another one press:
This configuration is done in W-4SEC.
This configuration is done in W-4SEC.
You must configure:
You must configure:
An expander is a W-4SEC module with a T-SEC keypad, so you can choose whether it is Total or Garage to limit the zones it can arm and disarm.
An expander is a W-4SEC module with a T-SEC keypad, so you can choose whether it is Total or Garage to limit the zones it can arm and disarm.
The default User code in the factory settings is “2345”. You should start by pressing on the “Key” symbol.
The default User code in the factory settings is “2345”. You should start by pressing on the “Key” symbol.
The default installer code in the factory settings is “98765432”. You should start by pressing on the “Key” symbol.
For your safety and the correct use of your security system change this code.
The default installer code in the factory settings is “98765432”. You should start by pressing on the “Key” symbol.
For your safety and the correct use of your security system change this code.
The default manager code in the factory settings is “123456”. You should start by pressing on the “Key” symbol.
For your safety and correct use of your security system change this code.
The default manager code in the factory settings is “123456”. You should start by pressing on the “Key” symbol.
For your safety and correct use of your security system change this code.
Check with your installer if for some reason your wiring or that detector is presenting an open circuit to B-SEC.
Check with your installer if for some reason your wiring or that detector is presenting an open circuit to B-SEC.
You have two ways to check on the T-SEC keypad or in the APP.
Walk in front of the detector and before it turns off the light check your T-SEC, it should display the name of the zone that detected the intrusion.
At the APP, go to the security view and walk in front of the detector, verifying that they typically turn on a red LED and check in your APP that zone status change.
If you want to check the W-4SEC or B-SEC through “shunt” you should note that all zones are factory inactive until the first time you see an “intrusion” (when someone passes in front of a detector even with the alarm disarmed), so all zones that are armed and then tested by opening the contact between it and the COM will always be in alarm until it is closed again.
You have two ways to check on the T-SEC keypad or in the APP.
Walk in front of the detector and before it turns off the light check your T-SEC, it should display the name of the zone that detected the intrusion.
At the APP, go to the security view and walk in front of the detector, verifying that they typically turn on a red LED and check in your APP that zone status change.
If you want to check the W-4SEC or B-SEC through “shunt” you should note that all zones are factory inactive until the first time you see an “intrusion” (when someone passes in front of a detector even with the alarm disarmed), so all zones that are armed and then tested by opening the contact between it and the COM will always be in alarm until it is closed again.
Para retirar um Alarme ou Tamper (violação ou Sabotagem do sistema) é necessário inserir duas vezes um código de utilizador.
Quando está em Alarme ou Tamper deverá ouvir a sirene.
Para retirar um Alarme ou Tamper (violação ou Sabotagem do sistema) é necessário inserir duas vezes um código de utilizador.
Quando está em Alarme ou Tamper deverá ouvir a sirene.
If you have removed or disconnected the T-SEC from a W-4SEC it will flag this action as an attempt to interfere (Tamper or Sabotage) with the proper operation of the security system. If this error persists contact our services for further screening.
To remove the error enter one of the user codes twice.
If you have removed or disconnected the T-SEC from a W-4SEC it will flag this action as an attempt to interfere (Tamper or Sabotage) with the proper operation of the security system. If this error persists contact our services for further screening.
To remove the error enter one of the user codes twice.
Zone Loop. Alarm Sabotage
This error appears when the contact that is checking the integrity and tampering of the sensors and siren is interrupted, this may be an intrusion attempt.
In case it is not an intrusion attempt check that your sensors and siren are intact and check the wiring. To mitigate the effects of this alarm until you can check the entire installation you can place a “shunt” between the “TampZ” contacts on your B-SEC.
To remove the error enter one of the user codes twice.
Zone Loop. Alarm Sabotage
This error appears when the contact that is checking the integrity and tampering of the sensors and siren is interrupted, this may be an intrusion attempt.
In case it is not an intrusion attempt check that your sensors and siren are intact and check the wiring. To mitigate the effects of this alarm until you can check the entire installation you can place a “shunt” between the “TampZ” contacts on your B-SEC.
To remove the error enter one of the user codes twice.
This error appears when the contact that is checking the integrity and tampering of the B-SEC metal box lid is interrupted, this may be an intrusion attempt. In case it is not an intrusion attempt, check that your B-SEC is closed or that it is not a maintenance.
To mitigate the effects of this alarm until you can check the whole installation you can place a “shunt” between the “TAMPC” contacts on your B-SEC.
To remove the error enter one of the user codes twice.
This error appears when the contact that is checking the integrity and tampering of the B-SEC metal box lid is interrupted, this may be an intrusion attempt. In case it is not an intrusion attempt, check that your B-SEC is closed or that it is not a maintenance.
To mitigate the effects of this alarm until you can check the whole installation you can place a “shunt” between the “TAMPC” contacts on your B-SEC.
To remove the error enter one of the user codes twice.
Subscribe to our newsletter and receive news, tips and offers Atouch
