Control for the luminous flux regulation of incandescent lamps, halogen, LEDs or other resistive or capacitive loads.
It is used to dim incandescent lights or resistive loads up to 300W. Not for use with 24V LED strips or ballasts.
Using the APP set the light in programming and then press a key from a touch panel.
Pressing the PROG key in the D-DIMRGB module and then pressing a key of a touch panel will set it in On/Off mode, to dimm the ligth you can use a long press.
Pressing the PROG key in the D-DIMRGB module and then sliding between keys of a touch panel will make that slide dim the ligth.
Using the APP set the light in programming and then press a key from a touch panel.
Pressing the PROG key in the D-DIMRGB module and then pressing a key of a touch panel will set it in On/Off mode, to dimm the ligth you can use a long press.
Pressing the PROG key in the D-DIMRGB module and then sliding between keys of a touch panel will make that slide dim the ligth.
Yes, any Dimmer can be used both with normal panel and T-OLED.
We can control the dimmer through the on / off mode, pressing PROG and a key. Or in slide between the keys increasing and decreasing the intensity.
Yes, any Dimmer can be used both with normal panel and T-OLED.
We can control the dimmer through the on / off mode, pressing PROG and a key. Or in slide between the keys increasing and decreasing the intensity.
Press PROG for more than 10 seconds until the LEDs blink.
This action will remove all module’s memory such as all keys that would act on the ligth are connected to it.
Press PROG for more than 10 seconds until the LEDs blink.
This action will remove all module’s memory such as all keys that would act on the ligth are connected to it.
In key and detector mode the input can send the following commands to one or more outputs:
Switch – Changes an output between on or off, up or down
On/Raise – Sends only the on and raise command
Off/Down – Sends only the off and down command
Timer – Sends a time during which the input turns on
Delay – Sends a time after which the input turns on
Scenario – Sends a scenario (always the same state that can be intermediate)
Follow Input – If the Input is on the Output will follow that state (can be in opposition and with blocking).
To set the desired function using the APP go to the left panel and select “Configure Keypads”, press on the key where the binary input is connected, follow
In key and detector mode the input can send the following commands to one or more outputs:
Switch – Changes an output between on or off, up or down
On/Raise – Sends only the on and raise command
Off/Down – Sends only the off and down command
Timer – Sends a time during which the input turns on
Delay – Sends a time after which the input turns on
Scenario – Sends a scenario (always the same state that can be intermediate)
Follow Input – If the Input is on the Output will follow that state (can be in opposition and with blocking).
To set the desired function using the APP go to the left panel and select “Configure Keypads”, press on the key where the binary input is connected, follow
To define the function of a binary input:
Prog 5 sec
Select with keys to the side….
on the “NEXT” key until the number of times corresponding to the function flashes
Press on OK.
Flashing 1 time = Switch
Blink 2 times = Switch on / up
Blink 3 times = Off / Down
Flashing 4 times = Timer
Pressing OK enters the time menu:
– Blink 1 = 1 second
– Blink 2 = 1 minute
– Blink 3 = 5 minutes
– Blink 4 = 10 minutes
– Blink 5 = 30 minutes
– Blink 6 = 60 minutes
– Blink 7 = Output memory time
Blink 5 times = Delayed
Blink 6 times = Scene
Blink 7 times = Follow Input
To define the function of a binary input:
Prog 5 sec
Select with keys to the side….
on the “NEXT” key until the number of times corresponding to the function flashes
Press on OK.
Flashing 1 time = Switch
Blink 2 times = Switch on / up
Blink 3 times = Off / Down
Flashing 4 times = Timer
Pressing OK enters the time menu:
– Blink 1 = 1 second
– Blink 2 = 1 minute
– Blink 3 = 5 minutes
– Blink 4 = 10 minutes
– Blink 5 = 30 minutes
– Blink 6 = 60 minutes
– Blink 7 = Output memory time
Blink 5 times = Delayed
Blink 6 times = Scene
Blink 7 times = Follow Input
When you associate the key with the module if it is in timer function the time is recorded, so you can have the time set and choose the “Output Memory Time” mode described in the previous question.
When you associate the key with the module if it is in timer function the time is recorded, so you can have the time set and choose the “Output Memory Time” mode described in the previous question.
These modules communicate via the BUS protocol which is referenced to a neutral, meaning you only need one more wire in your house to ensure you have BUS everywhere.
These modules communicate via the BUS protocol which is referenced to a neutral, meaning you only need one more wire in your house to ensure you have BUS everywhere.
Yes, it can be used to supplement an installation that in one module or the other.
Yes, it can be used to supplement an installation that in one module or the other.
Go to the left menu and select DELETE find the output(s) and put them on schedule, press the key, the output(s) will no longer appear as being on schedule in the APP.
Go to the left menu and select DELETE find the output(s) and put them on schedule, press the key, the output(s) will no longer appear as being on schedule in the APP.
Go to the left menu and select SET PANEL press a key on the panel that has the key you want to remove from all outputs.
Choose the key and in the COMMAND option choose DELETE then confirm with the check mark in the top right corner of the screen.
Go to the left menu and select SET PANEL press a key on the panel that has the key you want to remove from all outputs.
Choose the key and in the COMMAND option choose DELETE then confirm with the check mark in the top right corner of the screen.
Go to the menu on the left and select DELETE find exit and select the more options symbol on the right side of the screen. Confirm by selecting the option and validate by clicking on the checkmark in the top right corner.
Go to the menu on the left and select DELETE find exit and select the more options symbol on the right side of the screen. Confirm by selecting the option and validate by clicking on the checkmark in the top right corner.
Subscribe to our newsletter and receive news, tips and offers Atouch
