Thermostat control for temperature control. Can be used for any heating or cooling device with 0-10V input. Includes power switching relay.
The D-TH010V module is a thermostat to be placed in an electrical panel or next to the unit in a false ceiling (D= DIN). The particularity of this module is the control of machines with a 0 to 10V interface.
This works paired locally or remotely with a T-OLED panel. It is the T-OLED that reads and reports the temperature in the room where it is installed.
Among other functions, it performs weekly scheduling and summer/winter cycle control and allows the choice of three heating/cooling intensities.
No, this module does not even support a panel. Only modules with letter W at the beginning can support panels.
No, this module does not even support a panel. Only modules with letter W at the beginning can support panels.
Like any module in the climate range, the D-TH010V must be paired with a T-OLED.
It is the T-OLED that has a probe to read the temperature and informs the D-TH010V to decide on/off the machine according to the programmed parameters.
Like any module in the climate range, the D-TH010V must be paired with a T-OLED.
It is the T-OLED that has a probe to read the temperature and informs the D-TH010V to decide on/off the machine according to the programmed parameters.
D-TH010V must be paired with a T-OLED in slave mode
D-TH010V must be paired with a T-OLED in slave mode
There is no limit of units per module type in an Atouch home.
There is no limit of units per module type in an Atouch home.
The D-TH010V only has one zone, which can heat different rooms or floors, it has the connections to control interface boards at 0 to 10VDC. The panel that is paired in a room with this D-TH010V can control another secondary heating or cooling machine.
The D-TH010V only has one zone, which can heat different rooms or floors, it has the connections to control interface boards at 0 to 10VDC. The panel that is paired in a room with this D-TH010V can control another secondary heating or cooling machine.
D-TH010V must be paired with a T-OLED in slave mode
D-TH010V must be paired with a T-OLED in slave mode
The cycle can be changed via App 3.0 or on a T-OLED associated with any thermostat.
In APP 3.0, press the clima control button on the bottom bar and choose the cycle.
On the T-OLED enter configuration mode and toggle the cycle from summer mode to winter mode.
The cycle can be changed via App 3.0 or on a T-OLED associated with any thermostat.
In APP 3.0, press the clima control button on the bottom bar and choose the cycle.
On the T-OLED enter configuration mode and toggle the cycle from summer mode to winter mode.
The D-TH010V can be used in any machine that has a 0 to 10VDC interface of the type:
2-tube fan coil units
Radiators (starter dry contact)
Water underfloor heating via electrovalve
Air Conditioning (dry contact)
Consult us for more details or send us the reference of your machines.
The D-TH010V can be used in any machine that has a 0 to 10VDC interface of the type:
2-tube fan coil units
Radiators (starter dry contact)
Water underfloor heating via electrovalve
Air Conditioning (dry contact)
Consult us for more details or send us the reference of your machines.
In order to have two machines in a single room and in a single panel T-OLED with probe, a chained pairing is necessary, so the T-OLED is paired with the Thermo, which will be the main machine in the room, and then the secondary machine is programmed to follow the primary.
In order to have two machines in a single room and in a single panel T-OLED with probe, a chained pairing is necessary, so the T-OLED is paired with the Thermo, which will be the main machine in the room, and then the secondary machine is programmed to follow the primary.
To define the type and machine you will have to enter the configuration menu.
On the T-OLED panel, ensure that it is in climate control mode.
Make sure the thermostat is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
Use the (-) key to navigate to the “Unit Type” menu and choose by pressing the lower left key.
To define the type and machine you will have to enter the configuration menu.
On the T-OLED panel, ensure that it is in climate control mode.
Make sure the thermostat is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
Use the (-) key to navigate to the “Unit Type” menu and choose by pressing the lower left key.
To edit the schedule you will have to enter the menu.
On the T-OELD panel, ensure that it is in clima control mode.
Make sure the thermostat is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
The first option will appear as “Program” by pressing the lower left key and change between “On” and “Off”, confirm by pressing the lower left key.
The “Cycle” option will appear and you can choose Winter or Summer. Navigate to “Summer” and “Winter” and set the times and temperatures by day of the week for each of the cycles.
To edit the schedule you will have to enter the menu.
On the T-OELD panel, ensure that it is in clima control mode.
Make sure the thermostat is turned off by pressing the top left key.
Press for 5 seconds on the lower left key until you enter the menu.
The first option will appear as “Program” by pressing the lower left key and change between “On” and “Off”, confirm by pressing the lower left key.
The “Cycle” option will appear and you can choose Winter or Summer. Navigate to “Summer” and “Winter” and set the times and temperatures by day of the week for each of the cycles.
You can change the temperature in two ways via the APP or via the Panel where you measure the temperature to be changed:
a) APP – In the lower bar, navigate to Clima Control, find the room you want to change and increase or decrease the “Target Temperature” using the “+” and “-“;
b) On the room panel, ensure that it is in clima control mode.
see if it is on or off by pressing the key and press the “+” and “-” key to change the “Target Temperature”.
If you have the schedule turned on, these actions overlap until the next scheduled event.
You can change the temperature in two ways via the APP or via the Panel where you measure the temperature to be changed:
a) APP – In the lower bar, navigate to Clima Control, find the room you want to change and increase or decrease the “Target Temperature” using the “+” and “-“;
b) On the room panel, ensure that it is in clima control mode.
see if it is on or off by pressing the key and press the “+” and “-” key to change the “Target Temperature”.
If you have the schedule turned on, these actions overlap until the next scheduled event.
These changes are in effect until the next scheduled event occurs. If you do not have active schedules in the “Program” Menu, they will remain until you change them again.
These changes are in effect until the next scheduled event occurs. If you do not have active schedules in the “Program” Menu, they will remain until you change them again.
Yes, a T-OLED paired with 1 or 2 Thermo modules controlling 1 or 2 machines for the same room can always remain in secondary Air Conditioning
To permanently switch between Primary automation mode and Secondary clima control mode, press the lower left and upper right buttons simultaneously for 5 seconds. The presence or absence of
If you have automation mode and just want to change it temporarily press the keys momentarily.
Yes, a T-OLED paired with 1 or 2 Thermo modules controlling 1 or 2 machines for the same room can always remain in secondary Air Conditioning
To permanently switch between Primary automation mode and Secondary clima control mode, press the lower left and upper right buttons simultaneously for 5 seconds. The presence or absence of
If you have automation mode and just want to change it temporarily press the keys momentarily.
No, this module does not have binary inputs. The inputs are used to connect motion sensors, brightness, timers or others.
No, this module does not have binary inputs. The inputs are used to connect motion sensors, brightness, timers or others.
To reset this module to its original settings, press the PROG button for 10 seconds. This will clear the name, panel association and all machine parameters.
To reset this module to its original settings, press the PROG button for 10 seconds. This will clear the name, panel association and all machine parameters.
Subscribe to our newsletter and receive news, tips and offers Atouch
